By Tutorial for Installing a Bathtub
By Tutorial for Installing a Bathtub
Blog Article
Almost everyone seems to have his or her own thinking with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bath tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and occasionally, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably tough task. If the old tub is readily available, the project can move quickly; if you need to open up a wall to get rid of the old tub and also place the brand-new bathtub, the job is much harder. In either instance, the task is within a house handyman's abilities, although you will need a helper to move out the old bathtub as well as set in the new one. Make sure you have qualified on your own for the work as well as fit trying it. Rather than working with a service provider to take over a halfway-completed task, it is much better to take into consideration utilizing one before you start. Possibilities are you might require a professional plumber to make tube links.
This write-up will certainly aid you install a brand-new bathtub in your washroom if you have actually already purchased a brand-new tub and also don't need to transform the arrangement of your previous water supply pipelines.
Your tools and product checklist must comprise the following:
Getting ready for the Setup
To start with, the supporting framework provided with the bathroom must be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps unit to prevent pressure on the tub.
Fit the adaptable tap connectors to the bottom of both taps utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its last position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water system. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The process of eliminating the existing taps can be quite troublesome as a result of the limited access that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will originate from the pipes. Once the supply pipelines have been gotten rid of, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
Before proceeding to fit the new faucets, contrast the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Setting up the Tub
Using both wood boards under its feet, position the bathtub in the called for placement. The wooden boards are practical in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 little points.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by checking the spirit level as well as adjusting the feet on the bath tub up until the level reads level.
To mount taps, fit all-time low of the furthest flexible faucet connector to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Turn on the water system as well as inspect all joints as well as new pipework for leakages and also tighten them if required. Fill up the bathtub as well as also inspect the overflow outlet and the typical electrical outlet for leaks.
Lastly, repair the bath paneling as described in the producer's user's manual. Tiling and sealing around the bathtub needs to wait till the bath tub has actually been utilized at the very least when as this will resolve it right into its last placement.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washers are in area between the faucet and also the sink. Safeguard the tap in place with the supplier provided backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind must be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break an inflexible seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, causing issues with moisture and possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your fixtures and also installations. They are offered in tubes as well as cartridges, and also can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched paper or soft rope. Remember to constantly load the bathtub with water before securing, to permit the movement experienced when the tub is in use. The sealer can fracture fairly very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily offered on the market. It is advisable to fit the ceramic tiles using water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that piece about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a search on the search engines. If you enjoyed reading our blog entry please do not forget to pass it around. Thank you for your time. Kindly pay a visit to our blog back soon.
Tap issues? Ring! Report this page